We – EPG Group the biggest agricultural gearbox and pto manufacturing facility in China with 5 different branches. For more particulars: Mobile/whatsapp/telegram/Kakao us at: 0086-13083988828
Shut up of two yokes with the common joint. Observe the slight oozing of grease from the UJ seal ends, the clump of grease is from inside of the yoke splined shaft region –Generate (outer) yoke has a woman (common spline) hole and “Y” form stop that is the universal joint (UJ) mount. –UJ is a cross shaped casting obtaining roller bearings enclosed with caps at all 4 points and is held into the yoke with 4 “C” clips –Interior yoke and push shaft is another yoke welded to the push end, of the generate shaft. –Pushed shaft and interior yoke is the pushed shaft that rides inside of the travel shaft and has a yoke welded at the pushed finish –UJ another UJ as earlier mentioned SFI M100 PTO AdapterAs a precautionary evaluate, it is a good idea to acquire a PTO adapter to make certain compatibility with your particular tractor model.fiat bravo travel shaft It bmw x5 generate shaft alternative cost is 540 rpm to a thousand rpm adapter our 3 pt submit gap digger pto shaft purpose pto cross bearing replacement to double knuckle pto shaft provide driver side cv axle substitute a pto shaft areas diagram large pto drive shaft parts close to me selection 15 spline pto shaft of quality merchandise at cost-effective rates, supply the greatest services for clients happy and add to our ongoing advancement. Beneath the advice of managerial perception of “Serving agriculture, scoring a achievement by way of top quality of products and honesty in enterprise”, our goods have been dependable by customers and have gained a greater share of market place.
TY collection tractor is with power from 18HP to 35HP tractor, 2WD and 4 wheel drive
Electricity selection: 18, twenty, 22, 25, 28, and 30HP, 35HP
It can be matched with a lot of sorts of farm implements
Characteristics:
This sequence item is a center and tiny HP tractor straight connected with its motor
It has the characteristics of higher transmission efficiency, minimal tremble, substantial traction, large adaptability, and effortless start off
It is the upgraded technology change solution
Jaw kind differential lock can increase the go-capability
Hydraulic output interface can make direct connection with the dump trailer
This sequence tractor can have numerous diverse configurations according to customers needs:
One phase clutch or two stage clutch, (three + one) by 2 6 shifts or (four + one) by two eight shifts in which the creeping change can be chosen, 1 or two regular PTO rev
Set or adjusted tread, again catalog or one suspensions
Motor sort: Two or a few cylinder diesel engine
Model | TY184 | TY204 | TY224 | TY254 | TY284 | TY304 | ||
Type | 4×4 4 wheel drive | |||||||
Length | 2710/2796 | 2768/2854 | ||||||
Width | 1222/1296 | 1514/1696 | ||||||
Depth | 1338 | 1365/1414 | ||||||
(mm) | Wheel foundation | Front wheel | 1000/1200 | |||||
Main Proportions of Tractors | Rear wheel | 1000-1300 Adjustable | ||||||
Tread | 1512/1598 | |||||||
Min. Floor Foundation | 266 | |||||||
(kg)Dry Mass | 1100 | 1106 | 1130 | |||||
Motor | Model | 290/295 | 295 | 295 | 2100 | 2102 | ||
Type | Vertical, 2-cylinder, Drinking water Cooled and 4-stroke | |||||||
(kw) Rated Power | 13.two | fourteen.72 | 16.one | eighteen.four | 20.six | 22.06 | ||
(r/min)Rated Rev. | 2200 | 2300 | 2400/2500 | 2400 | ||||
Gasoline | Diesel Oil | |||||||
Tyre | Front Wheel | 6.00-twelve/6.00-sixteen | ||||||
Rear Wheel | eight.thirty-24/9.50-24 | |||||||
Clutch | Dry-friction, Single Phase or Dry-friction, Two Stage | |||||||
Steering | Mechanical Variety or Hydraulic Type | |||||||
Transmission Box | (3+one)×2or(four+one)×2or(four+1)×2×2(with creeper) | |||||||
Suspension Kind | Post Postitioned Tri-position Suspension Catalogue O | Post Postitioned Tri-level Suspension Catalogue O or I | ||||||
PTO Shaft | (r/min)Variety and Rev. | Non-unbiased Kind 540 or Non-unbiased Type 540/one thousand, 540/720 or Semi-unbiased Sort 540/one thousand,540/720 | ||||||
Spline Size |
I35 Rectangle Spline with six teeth(6×28.91×34.79×8.sixty nine) |
The use of unique equipment manufacturer’s (OEM) part figures or logos , e.g. CASE® and John Deere® are for reference functions only and for indicating merchandise use and compatibility. Our company and the shown substitute areas contained herein are not sponsored, accredited, or produced by the OEM.